7个步骤解决时控开关的故障问题
注意：当产品出现故障后，请先断开电源，再进行设备检查！
1 请检查“星期”是否正确
如果时控开关没有在设定的时间开启或关闭负载，那可能是“星期”没调对，请按照“定时设置”中介绍的方法检查或重调。
2 请检查多余的时间组是否取消
如果第一点确认无误，却依旧出现不能按时开关负载的情况，那可能是因为没有取消多余的时间组，请参照“定时设置”中介绍的方法进行删除。注意：只有显示为“-- : --”才表示取消成功; 如果显示“00：00”则表示0点（24点），并非取消成功。
3 请检查时控开关是否工作在自动模式
如果上述两点确认无误，而时控开关仍无法正常工作，那有可能是时控开关处于“手动模式”，可通过调节“自动/手动”键将设备先调节到当前所需的工作状态，然后再调节到“自动模式”。
4 请检查保险管
如果以上三点确认无误，可时控开关依旧无法正常工作，请打开后座保险盖（端子盖板），检查保险管是否己经熔断。如己熔断，请换上新的0.1A~0.3A的保险管。
5 请检查供电电源
如果遇到时控开关在工作时，工作灯亮（输出指示灯），但是开关无法正常切换的情况，请检查电源电压是否过低。如果时控开关被烧坏产品，请检查供电电源是否超出了产品的额定电压，以及电源线是否接错。
6 请更换电池
如果LCD液晶屏不显示或者显示不清，需更换相同规格的电池。（仅限可更换电池的时控开关）
7 请联系我们或当地经销商
如用以上几种方法还不能排除故障，请与本公司或者当地经销商联系处理。
7 steps to solve the failure of time control switch (Timer Switch)
Note: When the product fails, please disconnect the power first, and then check the equipment!
1 Check the week:
If the timer switch does not turn on or turn off the load at the set time, it may be that the "WEEK" is not adjusted correctly, please check or reset it according to the method introduced in "Timing Setting".
2 Check the time groups:
If the first point is confirmed to be correct, but the load still cannot be switched correctly on time, the reason will be that the extra time group has not been cancelled. Please refer to the method introduced in "Timing Setting" to delete it. PS: Only when the display shows "--: --", it means the time group is deleted successful; if it displays "00:00", it means 0 o'clock (24 o'clock), not the deleting success.
3 Check the switching mode:
If the above two points are confirmed to be correct, but the timer switch still does not work normally, it may be that the timer switch is working in "Manual Mode". You can first adjust the "AUTO/MANU" key to set the timer switch to the right working state of the load (ON or OFF), then switch to the "Automatic Mode".
4 Check the fuse:
If the above three points are correct and the timer switch still cannot work normally, please open the rear seat insurance cover (terminal cover) and check whether the fuse has been blown. If it is blown, please replace with a new 0.1A~0.3A fuse.
5 Check the power supply:
If the Work LED (or Output LED) is on when the timer switch is working, but the load cannot be switched normally, please check whether the voltage of the power supply is too low. If the timer switch is burned out, please check whether the power supply voltage exceeds the rated voltage of the product and whether the power cable is connected incorrectly.
6 Please replace the battery:
If the LCD screen does not display or the display is not clear, replace the battery with the same specification. (Only for timer switch with replaceable batteries)
7 Please contact us or local distributor:
If the fault cannot be eliminated by the above methods, please contact us or the distributor (dealer) in your local area.
转载请超链接注明：头条资讯 » 7个步骤解决时控开关的故障问题
免责声明
：非本网注明原创的信息，皆为程序自动获取互联网，目的在于传递更多信息，并不代表本网赞同其观点和对其真实性负责；如此页面有侵犯到您的权益，请给站长发送邮件，并提供相关证明(版权证明、身份证正反面、侵权链接)，站长将在收到邮件24小时内删除。